A Beginner's Guide to Plumbing for Bathtub Installation
A Beginner's Guide to Plumbing for Bathtub Installation
Blog Article
Just about every person will have their private concepts with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a bath tub isn't specifically brain surgery, however it does need strong plumbing, woodworking, and in some cases, tiling skills. Changing an old bath tub with a new one is also a reasonably difficult project. If the old tub is conveniently available, the project can move rapidly; if you have to open a wall to remove the old tub and also position the new bathtub, the job is a lot harder. In either instance, the project is within a residence handyman's abilities, although you will certainly require a helper to leave the old tub and embeded in the new one. Make sure you have actually qualified yourself for the work and fit attempting it. Rather than employing a specialist to take control of a halfway-completed job, it is better to think about employing one prior to you start. Chances are you might need a specialist plumber to make tube connections.
This write-up will certainly help you set up a brand-new bath tub in your restroom if you have currently gotten a brand-new bathtub and don't require to alter the setup of your previous water supply pipes.
Your tools and also product list should comprise the following:
Getting ready for the Installment
Firstly, the supporting structure provided with the bath should be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps unit to stop strain on the bathtub.
Fit the versatile tap connectors to the bottom of both taps utilizing 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its last setting.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you should do is detach the water system. After doing so, turn on the taps to drain any kind of water staying in the system. The procedure of removing the existing taps can be fairly troublesome due to the restricted access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly come from the pipes. When the supply pipes have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any old securing compound.
Prior to moving on to fit the new taps, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Making use of the two wood boards under its feet, position the bath tub in the required placement. The wooden boards are practical in uniformly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 small factors.
The next objective is to make certain that the tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the bath tub until the level checks out level.
To install taps, fit all-time low of the furthest flexible faucet adapter to the proper supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water as well as examine all joints as well as new pipework for leakages and also tighten them if essential. Load the tub as well as also check the overflow outlet and also the normal outlet for leaks.
Finally, take care of the bathroom paneling as explained in the maker's user's manual. Tiling as well as sealing around the bathtub ought to wait up until the bath tub has actually been used at least once as this will certainly settle it right into its final position.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making sure that the washers are in place in between the faucet as well as the sink. Secure the tap in place with the maker supplied backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with regular faucet ports. The former kind should be attached to the faucet finishes initially, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bathroom meets the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to break a rigid seal, causing the water to pass through the wall in between the bathroom and also the tiling, causing problems with wetness and feasible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your components and also fittings. They are marketed in tubes as well as cartridges, and also are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to permit the activity experienced when the bathtub remains in use. The sealant can break relatively very early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise conveniently readily available on the market. It is advisable to fit the tiles utilizing water-resistant or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I stumbled upon that piece on Tools You Need to Install a New Bathtub while doing a search on the search engines. Appreciated our blog? Please share it. Let somebody else discover it. I am grateful for your time. Come back soon.
Urgent plumbing disruptions? Contact now Report this page